A New Link Scheduling Algorithm for 60 GHz-WPAN Communication System

,


Introduction
With the increasing production of full-HD even Ultra-HD film and television programs, the wireless communication demand with high transmission rate and low latency experience has become especially urgent.Unfortunately, due to the limitations of spectrum resource, transmitting power, and technical standard, Wi-Fi, UWB, and other short-range wireless communication technologies could not achieve Gbps transmission rate [1][2][3].The fifth generation of mobile communication technology is now under brewing and researching, which is a general tendency for using higher frequencies [4][5][6].With apparent advantages of several GHz license-free spectra, low power consumption, low-cost implementation of CMOS devices, and so forth [7][8][9][10], 60 GHz wireless communication technology has become the first choice for Gbps level short-range wireless communication.At the same time, some researches about 60 GHz wireless communication have been proceeded in wireless sensor network field.A threeelement distributed phased array is prototyped based on 60 GHz wireless sensor in [11] to achieve phase-frequency synchronization among physically isolated sensors network.Paper [12] reports the first experimental results on the prototype for a novel wireless sensor network that offers both data collection and localization capability with 60 GHz frequency band.These motivations have mobilized the effort of several standardization groups such as the IEEE 802.15 Task Group 3c (802.15.3c) [13], ECMA387 [14], and IEEE802.11ad[15].Recently IEEE 802.15.3c has been formed to develop a 60 GHz mmWave wireless personal area network (WPAN) standard including physical layer MAC layer.This standard has now become one of the most mature 60 GHz standards.

International Journal of Distributed Sensor Networks
And the expected physical data transfer rate could reach 5.7 Gbps with this standard.
In the traditional WPAN center-based network, central node is the only data forwarder and only one link (uplink or downlink) is allowed in one time slot.Traditional WPAN media access control (MAC) mechanism usually adopts time division multiple access (TDMA) [16][17][18], while 60 GHz-WPAN system adopts a hybrid network architecture which combines central-control with peer-to-peer connection.The central node is only responsible for network control and management and the data transmissions without going through the central node.Due to the large propagation attenuation of 60 GHz signal, the interference between the two distant 60 GHz devices is small.In order to remedy the high propagation attenuation, directional transmission based on array antenna beamforming technology is almost essential for 60 GHz communication.Due to directional transmission, about 99.9% of the energy is concentrated in 4.7 ∘ beam range [9].The interference in different directions will be small, which is conducive to directional spatial multiplexing for devices.TDMA multiple access method is not the best multiple access method for directional high-speed communication [19].Space division multiple access (SDMA) could combine with TDMA and the WPAN system capacity could be improved [1,20,21].In order to take advantage of the characteristic of directional transmission, the MAC mechanism for 60 GHz wireless communication should be designed different from the MAC mechanism of low band, such as Wi-Fi at 2.4 GHz and 5 GHz.However, few 60 GHz multiple access schemes including 802.15.3c standard use this characteristic of 60 GHz at this stage besides [22,23].
In this paper, in order to realize quick free switch between two communication devices (DEVs) of WPAN system, an interconnected mechanism based on switched beamforming technology is structured firstly.The rationale of spatial reuse in 60 GHz-WPAN system is presented.In order to improve the efficiency of spatial reuse, an average time slot multiplexing allocation (ATSMA) algorithm based on space/time division multiple access (STDMA) solution is proposed.According to this algorithm, resource management and link scheduling are carried out in 60 GHz-WPAN system.
The main contributions of the paper include two parts.Firstly, a DEV interconnected mechanism of 60 GHz-WPAN system based on switched beam code is proposed and 60 GHz-WPAN system model is established based on switch beam, which guarantees free switching between the devices under directional communication.Secondly, the multiple access solution under 802.15.3c standard is improved.SDMA is inserted into the 802.15.3c standard.An ATSMA algorithm is presented which uses the spatial characteristic of 60 GHz signal effectively.Under the premise of certain time slot allocation fairness, the ATSMA algorithm improves the capacity of the 60 GHz-WPAN system significantly.
The organization of the paper is as follows: Section 2 introduces the characteristics of 60 GHz communication, the directional 60 GHz transmission system, and the MAC protocol by 802.15.3c.In Section 3 the 60 GHz-WPAN system model based on switch beam is established; meanwhile, a devices-interconnected mechanism could realize quick free switch between two devices of 60 GHz-WPAN system.Section 4 presents the rationale of spatial reuse in 60 GHz-WPAN.Section 5 presents the judgment method of link coexistence and proposes ATSMA link scheduling algorithm.Section 6 lists the simulation setup and parameters.On this basis, simulation results are presented.Finally Section 7 concludes this paper and marks the potential future works.

Characteristics of 60 GHz
Wireless Communications (1) The average transmitting power and receiving power are denoted as   and   .  is the transmitter's antenna gain.  is receiver's antenna gain. is the wavelength of signal. is the distance between transmitter and receiver.The higher carrier frequency is, the lower  is and further the lower received signal power   will be.According to formula (1), the path loss of 60 GHz signal is at least 28 dB higher than the path loss of 2.4 GHz signal and 21 dB higher than the path loss of 5 GHz signal.Furthermore, 60 GHz signal suffers from 15 to 30 dB/km atmospheric absorption on the atmospheric conditions [9].Therefore 60 GHz communication system is not suitable for long distance wireless communication but is very suitable for short distance indoor wireless communication.

Directional Transmission Based on Switched Antenna
Array.Since 60 GHz signal suffers large propagation attenuation in the process of transmission, some methods should be carried out to avoid the waste of energy.For 60 GHz communication, only 5 mm wavelength makes it feasible to integrate a large number of antenna elements on the whole package for both 60 GHz transmitter and receiver [25].Antenna array beamforming technology is preferred for 60 GHz wireless communication because of the large antenna gain, small size, and fast electronic steerability.The antenna array beamforming provides directional transmission, which can overcome the high path loss problem.The antenna array beamforming is also conducive to directionality spatial multiplexing and improves the system capacity.At the same time, the antenna array beamforming is especially meaningful in solving the notable NLOS obstruction problem.
Generally, smart antenna beamforming technology involves switching beamforming and adaptive beamforming [26].Currently, 60 GHz communication systems commonly adopt switching beamforming based on beam code due to the low complexity [9].Switching beamforming is a method  which divides user area into multiple narrow beam partitions.Each of partitions corresponds to a fixed beam, whose weight vector is preconfigured by the system.By beam training or position estimation of the target user, antenna array can select and switch optional weight vector.Two 60 GHz wireless communication standards which are proposed by IEEE802.15.3c and 802.11ad adopt switching beamforming to compensate high path loss and overcome link block.802.15.3c even has provided the designing scheme of beam code and beam training mechanism [9].

60
GHz MAC Protocol by 802.15.3c.According to IEEE 802.15.3c, the channel access and data transmission are based on the superframe structure [9], which is composed of three parts: Beacon Period (Beacon), the controller broadcasts commands and access information by sending the beacon frame; Competitive Access Period (CAP), this is a contention-based channel access period, adopting Carrier Sense Multiple Access/Collision Avoidance (CSMA/CA) scheme; and Channel Time Allocation Period (CTAP), the channel access mechanism is based on TDMA mode.PNC divides CTAP into several channel time allocations (CTAs).The length of a superframe can be set to a fixed value or a variable according to specific requirements.Considering the application of beamforming technology for directional transmission, two structures are presented, which are superframe under omnidirectional antenna pattern and superframe under quasi-omnidirectional antenna pattern.The major difference is that the beacon frame will be sent in different directions in turn to make sure that all devices can get access to the network in the latter pattern.Figure 1 presents the quasiomnidirectional antenna pattern superframe architecture by 802.15.3c.

60 GHz-WPAN System and
Devices-Interconnected Mechanism IEEE 802.15.3c standard builds the network by using the piconet as its basic unit, which is a collection of all devices connected together.To support self-organized network, all devices are equal with the same priority and could communicate with each other.Devices are divided into piconet controller (PNC) and common DEV, where PNC is responsible for managing the whole network, including timing management, resource allocation, and task scheduling.In order to ensure the self-organization and robustness of the network, PNC is dynamically selected from network nodes and supports seamless switching between devices when the former PNC suddenly leaves or fails to work.Generally, WPAN system supports intercommunicate between any two DEVs.For common WPAN system, omnidirectional antennas are equipped by all DEVs.No matter the receiving DEV located in any orientation of sending DEV, the signal always could be received.60 GHz system generally adopts directional communication.If every DEV always points to fixed direction in the whole communication process, it is apparently unable to realize intercommunication for 60 GHz-WPAN.At this point, array antenna beamforming technology will become the preferred technology for 60 GHz-WPAN.In order to reduce the complexity of building networks, switching beamforming based on beam code is adopted.
As shown in Figure 2, there are  DEVs in the WPAN, each of them purchasing an antenna array to achieve directivity control.We select DEV1 as PNC and conduct beam training based on 802.15.3c beam code under unobstructed environment [9].After beam training, the interconnecting optimal beam pairs of devices are found and the antenna weight vectors corresponding to these optimal beam pairs are recorded, as shown in Table 1.
1(2) and  2(1) , respectively, indicate the weighted vector value when DEV1 and DEV2 intercommunicate with their optimal beam pairs.The subscript 1(2) indicates the optimal weighted vector for DEV1 pointing to DEV2.The process of beam training is carried out in the initial stage of 60 GHz-WPAN establishing.So when every DEV communicates with other DEV under unobstructed environment, there is no need for beam training.We can invoke the antenna weight vectors from Table 1; then the directional matching communication between every two DEVs could be realized.This mechanism brings great convenience and saves the beam training time in the process of switching DEVs.
In the next superframe- + 1, we assume that there are also 3 pairs of links sending out transmission request.Because some links have completed the transmission task and some new transmission tasks are allocated, compared with superframe-, the transmission links have changed as DEV1-DEV4, DEV2-DEV3, and DEV5-DEV7 at this time.Weight vectors are also directly selected from the weight vector record form in Table 1, which are ⟨ 1(4) ,  4(1) ⟩, ⟨ 2(3) ,  3(2) ⟩, ⟨ 5 (7) ,  7(5) ⟩.Take DEV1 as examples, the weighted vector  1(2) is transformed to  1(4) ; then the beam direction of DEV1 is turned to DEV4' beam direction.Other DEVs also experience this process and complete their beam switching process, respectively, as shown in Figure 3.
Through establishing a weighted vector form of interconnection beam pairs for WPAN DEVs, a DEV interconnection mechanism based on the beam code for 60 GHz-WPAN is set up.This mechanism can help to realize fast free switch for every communication DEV.On one hand, it is satisfied for the directional transmission of links; on the other hand, it is also convenient for switching the communication DEVs.The spatial reuse characteristic of 60 GHz-WPAN will be investigated based on directional transmission mechanism in the following sections.

Spatial Reuse Rationale for 60 GHz-WPAN
As shown in formula (2), Shannon theorem indicates the channel capacity in continuous channel under Gaussian white noise, namely, the maximum theoretical transmission rate: where SINR = /( 0  + ) is the Signal to Interference plus Noise Ratio (SINR) of the receiving terminal, which is also the main restriction of system capacity if the channel bandwidth is fixed. is the energy of useful signal. is the energy of interference signal. 0 is one-sided noise power spectral density;  indicates the signal bandwidth.Assume that there are  links with communication request and the time of data transmission in one superframe is .If only one link is allowed to transmit at one time slot, that is, links are distributed in traditional TDMA mode, the transmission duration of each link is /.Since link  only exists in one time slot for every superframe, the capacity of link  in one superframe is indicated in (3) and the total capacity of one WPAN system consisting of  links is in (4): For STDMA link allocation, each link can share time slot with other communicating links concurrently according to certain criteria.Assuming link  can be allocated to   (  ≤ ) time slots for communication, then the capacity of link  in one superframe is indicated as in formula (5), where ∑  ̸ =  , is the receiving interference power of link  which comes from other links in the same time slot.For different time slots, there are different interference sources, so ∑  ̸ =  , has different values.The total capacity of one WPAN system consisting of  links can be indicated as in (6): ) .
From ((3), ( 5)) and (( 4), ( 6)), to ensure spatial multiplexing gain of the single link  or the whole WPAN system,    >   or   >  should be met.For the single link , the values of   , ,  0 , ,  are fixed, so the main factors which affect formula (5) are the value of ∑  ̸ =  , and   .However, ∑  ̸ =  , and   are interconstraint.If the number of time slots allocated to each link increases, the average number of links to each slot will increase and lead to larger mutual interference for these links in this slot.Furthermore, the link capacity will reduce contrarily.So the key to achieve high spatial multiplexing gain is designing a rational link and time slot allocation scheme.Links with small interference are scheduled into the same slot, and this scheme guarantees that each link is allocated to as many slots as possible.

Link Coexistence Determination and ATSMA Link Scheduling Algorithm
When adopting STDMA, the capacity of WPAN system is mainly decided by interference power ∑  ̸ =  , and   .Paper [22] figured out a sufficient condition to obtain spatial multiplexing,  , ≤  0  (interference power must be less than the background noise power), and an Exclusive Region (ER) is set up at the receiver of each link.According to the position and antenna gain of each transmitter and receiver, the ER radius is calculated.Concurrent transmission is allowed when one link is outside the ER of another link, and concurrent transmission enhances the WPAN system capacity.It is a simple and effective scheme to obtain spatial multiplexing gain, but this scheme fails to take into consideration the specific modulation and coding scheme.At the same time, this scheme is not necessarily to get maximum transmission multiplexing gain at ER radius but simply to ensure the link multiplexing gain greater than 0 dB using the space characteristic.
Paper [23] proposed a Virtual Time Slot Allocation (VTSA) algorithm based on the MAC design of IEEE 802.15.3c.A Probing Signal Broadcasting Period (PSBP) is added in the front of CTAP to measure the mutual interference between links in the same superframe.After getting the information of mutual interference between links, PNC will allocate virtual time slot for the remaining links.However, VTSA algorithm neglects the effect of noise during the decision process of coexistence and does not consider the effect of directional antenna for spatial multiplexing.So in this section, an average time slot multiplexing allocation (ATSMA) based on STDMA solution is proposed.We reference the ideas of establishing common channel interference (CCI) table by VTSA algorithm and set up a link interference tolerance (LIT) table which is used to calculate the link interference upper limit under different transmission rate.The actual link interference in CCI table is compared with the interference tolerance of this link in LIT table, in order to determine whether two or more links could coexist.At the same time the utilization rate of each CTA time slot is maximized on the premise of slot allocation fairness and the WPAN system capacity is improved as much as possible.

The Common Channel Interference (CCI) Probing Scheme.
In proposed ATSMA algorithm, a PSBP is also added in front of CTAP for every frame.During this period, PNC receives communication request and records link number  firstly.Each link is scheduled by PNC to send a short probing signal in their own transmission direction in sequence.Meanwhile, other links receive and record the signal in their own transmission direction in sequence.Then the receiver of each link records the statistical interference information.PNC establishes a CCI table.The CCI measurement data will be employed for CTAP of this frame.If there are  links with communication request, the CCI table will be a  ×  matrix as shown in the following: where   ( ̸ = ) is the interference value of link  to link  and   ,  = 1, 2, . . .,  represents the value of received useful signal of link .All the measurement data have contained the effect of white noise.If the transmit power changes, the CCI table also needs to be updated, because   ,  = 1, 2, . . .,  represents the value of received useful signal of link .If we want to obtain the authentic common channel interference (CCI) table, the received useful signal should be taken out.So the diagonal element   ,  = 1, 2, . . .,  is adjusted to 0 and the new CCI table is obtained as follows:  sum of coexistent links (included this scheduling link) in CTA() exceeds the allowed LIT of each coexistent link.If the CCI sum in CTA() exceeds the allowed LIT, this link is given up scheduling to CTA(), otherwise this link is scheduled to CTA().Then the value of  is changed as  = 2, . . .,  − 1 in sequence; repeat the process of coexistence testing for CTA() until the CCI sum of coexistent links exceeds the allowed LIT of each coexistent link.(3) Change the value of  as  = 1, 2, . . .,  − 1 in process (2) successively and then complete the process of coexistence testing and link scheduling for  CTAs.
In order to guarantee more links could share the same time slot, link with smaller CCI value is firstly allocated to the CTA().This algorithm firstly allocates each CTA to each link as TDMA scheme in proper order; then link  is defined as the main link of CTA().All the links which are allocated in the same CTA will not affect the specified communication rates of other links.PNC allocates the links which could parallel transfer to the same CTA.On one hand, ATSMA algorithm ensures that each link could be allocated to one time slot at least, so the ATSMA algorithm can guarantee certain link allocation fairness.On the other hand, ATSMA algorithm allocates more slots to one CTA as much as possible and maximizes the system capacity.The proposed ATSMA algorithm has a computational complexity of ( 2 ).

Simulation Result and Performance Analysis
After the link scheduling algorithm is confirmed, system performance evaluation and simulation are carried out.

Simulation Environment
(1) Antenna Model.Assume that all devices in 60 GHz-WPAN system are deployed with the same antenna equipment.Two antenna patterns are taken into consideration, which are omnidirectional antenna and directional antenna with switching beam.802.15.3c beam codebook is used to structure switching beam.The number of antennas in antenna array is 8 and the number of beam is 16.
(2) Spatial Distribution Model of 60 GHz-WPAN System.Wireless 60 GHz nodes are randomly distributed in the 10 m × 10 m indoor square area.Assume that there are 5, 10, and 20 links (namely, 10, 20, and 40 nodes) having transmission request in one superframe.The transmitting power of each node is 10 dBm.Considering that the antenna gain of omnidirectional antenna in 60 GHz system could not support long range communication, the distance between transmitting node and receiving node with omnidirectional antenna will be set to be less than 4 m in order to ensure the required SINR for stable transmission.Due to the directional antenna gain being big enough for compensating the high path loss, the transmitting node and receiving node of each link with directional antenna are randomly selected from 10 m × 10 m indoor square area.Assume that all the nodes in communication status do not block other nodes in space.According to the piconet structure, PNC is randomly selected from the nodes and is responsible for peer-to-peer communication management and time slot allocation.In order to avoid the accidental effect caused by the position of nodes, 1000 times simulations with different random seeds are proceeded and the average capacity is calculated.
(3) Channel Model.IEEE 802.15.3c channel model is adopted [27], which is constructed by the measurement of 60 GHz signal propagation characteristics.Simulations are conducted in indoor living environment LOS channel CM1.
(4) MAC and PHY Layer Parameters.Since different modulation and coding schemes may be adopted by different links in actual WPAN system, we set three kinds of links which adopt different 60 GHz OFDM schemes, MCS1, MCS2, and MCS3, respectively.The percentages of three kinds of links are  40%, 40%, and 20%, respectively.Specific parameter setting is shown in Tables 2 and 3.
(5) The Selection of Gaussian White Noise Level.Generally, Gaussian white noise can be calculated by NF = KTBF, where  is the noise factor, which is defined as  = 1 here,  = 1.38 × 10 −23 J/K is the Boltzmann constant,  = 17 ∘ (290 K) is the room temperature, and  is the bandwidth of 60 GHz signal and is defined by the 802.15.3c as 2.16 GHz here.By the given parameter values, we can figure out the noise coefficient of 60 GHz communication system under normal room temperature state, NF = −80.6 dBm.So we set −94 dBm∼ −70 dBm as the Gaussian white noise range in the simulations.

Simulation Result and Performance
Analysis.System capacity is selected as the evaluation criteria to verify the validity of this algorithm.TDMA scheme and ER theory scheduling scheme based on STDMA multiple access are adopted to contrast the proposed ATSMA algorithm.
Figure 5 presents the 60 GHz-WPAN system capacity using different link scheduling schemes in one superframe under omnidirectional antenna.Since the selected noise levels meet the minimum SINR requirement under certain transmission rate, so the system capacity does not change with the noise level if TDMA is adopted as the time slot allocation scheme.The system capacity of TDMA scheme is about 21 Mb in one superframe.When the system noise level is low (−94 dBm∼−80 dBm), the system capacity based on ER theory scheduling scheme will not change with the increase of noise level and also will not change with the increase of link number.The system capacity based ER theory is equal to the system capacity of TDMA scheme when the system noise level is low.This is because the ER radius is larger than the longest distance of room model (diagonal distance).When the noise level is −94 dBm∼−80 dBm, all the links are judged which cannot coexist for parallel transmission.The ER theory radius decreases with the increase of noise.When the noise level is greater than −80 dBm, the links which can coexist for parallel transmission begin to increase and system capacity also begins to increase.ER theory scheduling scheme gradually presents the effect of spatial reuse, and the increasing trend of capacity caused by spatial reuse is greater than the decreasing trend of capacity caused by noise.The total system capacity in one superframe also presents increasing trend with the increasing of links number.This is because the links falling into ER region are increasing with the increasing of links number.The links for parallel transmission will also increase.For ER theory scheduling scheme, at most 1.31-fold, 1.42-fold, and 1.52-fold of capacities can be achieved compared with TDMA when the numbers of links are 5, 10, and 20, respectively.No matter how many links exist in WPAN system, the reuse performance and system capacity will decrease when noise level is greater than a certain value.This is because the decreasing trend of capacity caused by noise is greater than the increasing trend of capacity caused by spatial reuse.For ATSMA link scheduling algorithm, system capacity is greatly improved comparing with ER theory scheduling scheme and TDMA scheme when the noise level is relatively low.At most 2.11-fold, 2.72-fold, and 3.15-fold of capacities can be achieved compared with TDMA when the numbers of links are 5, 10, and 20, respectively.This is because the probability that links are arranged to transmit concurrently in the same CTA increases as the link increases.Furthermore the system capacity will increase.Because the interference tolerance of each link is fixed, less link mutual interference can be allowed with higher noise level.Therefore, the system capacity will decrease as the noise level increases.When the noise level is much lower than the link mutual interference, the negative effect of background noise is small.So the decreasing trend of capacity is not obvious in the range of −94 dBm∼ −85 dBm.Although the decreasing trend of ATSMA algorithm is accelerated when the noise level is higher, obvious improvement still can be achieved over ER theory scheduling scheme.Simulation also presents that the system capacity will not increase linearly as the links number increases.
Figure 6 presents the system capacity of 60 GHz-WPAN in one superframe using different link scheduling schemes under directional antenna.Similar trend is presented with omnidirectional antenna.The system capacity of TDMA scheme is also about 21 Mb in one superframe.For ER theory scheduling scheme, at most 3.6-fold, 6.6-fold, and 8.2-fold of capacities are achieved comparing with TDMA when the numbers of links are 5, 10, and 20, respectively.For ATSMA link scheduling algorithm, at most 4.4-fold, 8.3-fold, and 14.7-fold of capacities are achieved comparing with TDMA when the numbers of links are 5, 10, and 20, respectively.For directional antenna system, the performance of ATSMA algorithm is still superior to ER theory scheduling scheme and TDMA; meanwhile, the advantage become more obvious when there are more links in the system.Comparing with omnidirectional antenna mode, the system capacity presents the increasing trend when the noise level is low (−94 dBm∼−80 dBm).The multiplexing gain caused by directional transmission is significantly increased comparing with omnidirectional antenna whether adopting ATSMA algorithm or ER theory scheduling scheme.This also verifies the high spatial reuse character of 60 GHz signal under directional transmission.Although the complexity of ATSMA algorithm is a little bit higher than ER theory scheduling scheme (an extra PSBP needs to be established and the link mutual interference needs to be measured), the capacity gain is obvious, no matter whether under omnidirectional or directional antenna.

Conclusion
This paper proposes a DEV interconnected mechanism of 60 GHz-WPAN system based on switched beam code, which guarantees free switching between the devices under directional transmission.Then the multiuser access solution under 802.15.3c standard is improved using the directional transmission mechanism.SDMA is inserted into the 802.15.3c multiuser access solution.An ATSMA algorithm based on STDMA solution is proposed.With the premise of certain time slot allocation fairness, ATSMA algorithm utilizes the spatial characteristic of 60 GHz signal effectively and improves the capacity of 60 GHz-WPAN system significantly.The simulation results indicate that the multiplexing gain caused by directional transmission is significantly increased comparing with omnidirectional antenna based on STDMA scheme.
Due to the large material penetration loss of 60 GHz signal, 60 GHz communication link is prone to be interrupted by blocking.How to achieve high system throughput, meanwhile solving the link blocking problem, is a new challenge [28][29][30].Constructing collaboration WPAN antiblocking communication model and redesigning the link scheduling algorithms are our next work.

Figure 5 :
Figure 5: 60 GHz-WPAN system capacity with different link scheduling schemes in one superframe under omnidirectional antenna.

Figure 6 :
Figure 6: 60 GHz-WPAN system capacity with different link scheduling schemes in one superframe under directional antenna.
[24]Characteristics of 60 GHz Signal.60 GHz signal belongs to millimeter wave band.The wavelength of 60 GHz signal is much shorter than mobile communication signal and Wi-Fi signal.60GHzwireless communication occupies up to 7 GHz of unlicensed spectrum, which is sufficient for future high rate communication system.The propagation attenuation in millimeter wave band is much larger than low frequency.Friis free space propagation[24]formula explains the reason of high path loss for 60 GHz signal.Consider

Table 1 :
Antenna weight vectors record form of interconnecting DEVs beam pairs.
)5.2.Link Coexistence Determination.Because the main application of 60 GHz communication is wireless HD video transmission, which proposes higher request for the stability of transmission rate, each transmission link should make stable and reliable transmission rate as the basic requirements.So, under specific modulation and coding scheme, the condition of link coexistence determination is set to be that the mutual interference between links does not affect the required transmission rate of this link.That is to say, the SINR of receiver must satisfy certain condition; we set the condition as SINR() ≥   /( 0  +   ) = SINR th (), where   is the received useful signal energy of each link ; that is,   ,   is the allowed maximum link interference tolerance of link  and SINR th () is the minimum SINR threshold for link  with required transmission rate.Since the actual 60 GHz system can adopt different transmission schemes and different modulation and coding modes, each link could have different transmission rates, respectively, and needs different SINR th .Taking 60 GHz-OFDM system, for example, in order to achieve the transmission rate of 1540 Mb/s, 3080 Mb/s, and 5775 Mb/s, the required minimum SINR is 3.3 dB, 9.0 dB, and 14.4 dB, respectively.When the transmission rate of link  changes, the SINR Select the link corresponding the j smallest element in column i from CCI table as the scheduling link, test if the CCI sum of coexistent link (included scheduling link) in CTA(i) exceeds the allowed LIT of each coexistent link th () will also change; meanwhile the interference tolerance of the corresponding link  will change correspondingly.Consider  =   − SINR th () ×  0  SINR th () .(9)Formula(9)gives the interference tolerance   of each link (i.e., the maximum permissible interference when selecting a predetermined transmission rate), for each link in the same CTA, ∑ CTA CCI <   .Then the link interference tolerance (LIT) table of each link is obtained as  = [ 1 ,  2 , . ..,   ].(2)For CTA(), select the link which corresponds to  ( = 1) smallest element in column  from CCI table as the scheduling link (except diagonal element); that is to say the scheduling link has  smallest mutual interference with link .Test whether or not the CCI

Table 2 :
OFDM modulation and coding parameters.

Table 3 :
MAC and PHY layer parameters.